Stanback Knives Nifeboy.com
The RANDALL KNIFE FORUMS

A place where EVERYBODY is welcome to join in on the discussion of Randall Made knives


Page 11 of 51 < 1 2 ... 9 10 11 12 13 ... 50 51 >
Topic Options
Rate This Topic
#84532 - 01/04/11 06:29 PM Re: Knife of the Week Model 18 * [Re: WildBill]
JR3 Offline
Knife Enthusiast

Registered: 01/02/11
Posts: 78
Loc: Northeast USA
Bill,

No permanent marks. The blade is carbon as I do not like stainless knives. Yes, I was able to get a fire. I wish I had a picture just a few seconds later. Mrs. JR3 took that one.

Top
#84535 - 01/04/11 06:50 PM Re: Knife of the Week Model 18 [Re: JR3]
WildBill Offline
Knife Enthusiast

Registered: 12/12/10
Posts: 51
JR3 Congrats.

Capt Chris - you are right, a stainless knife will (should) not create sparks, however, I didn't know if a purpose made flint would change that equation. I have one here though, I think I will give it a try and advise.

Bill



Edited by WildBill (01/04/11 06:51 PM)
_________________________
Bill
RKS#5892

Top
#84536 - 01/04/11 07:02 PM Re: Knife of the Week Model 18 [Re: WildBill]
JR3 Offline
Knife Enthusiast

Registered: 01/02/11
Posts: 78
Loc: Northeast USA
Gents,

Stainless blades work fine with Ferrocerium rods. It is a man made "flint" that only requires a 90 degree angle, or edge to make a good spark.

Now natural flint requires a hard carbon blade, or striker. No stainless for natural flint.
_________________________
Matt

Top
#84537 - 01/04/11 07:13 PM Re: Knife of the Week Model 18 [Re: JR3]
WildBill Offline
Knife Enthusiast

Registered: 12/12/10
Posts: 51
Ok, we are off topic a litte (sorry), but this is interesting.

I have one of the man made ferro rods that stays on the model 5 when hunting - just in case. I just tried it using a Model 10-5 (stainless) and it did work. I then compared it to the standard carbon blade which worked noticeably better. However, both did work.

Agree though: natural flint + stainless steel blade = one cold night.
_________________________
Bill
RKS#5892

Top
#84546 - 01/04/11 08:52 PM Re: Knife of the Week Model 18 [Re: Captain Chris Stanaback]
Leatherman Offline
Knife Enthusiast

Registered: 01/06/06
Posts: 1371
Loc: IL
Originally Posted By: Captain Chris Stanaback
I don't think the stainless blades will create the spark needed to ignite the tinder. Of course, like many times in life, I could be wrong.
Best, Capt. Chris


This guy is striking with a 154CM steel blade and a laminated VG10 core blade with 420 J2 side steel (the 420 is on the spine) he's getting some good sparks! Long video but a neat comparo IMO.

http://www.youtube.com/watch?v=AIGrL1fJCu4
_________________________
Ben

Top
#84547 - 01/04/11 09:02 PM Re: Knife of the Week Model 18 [Re: JR3]
Leatherman Offline
Knife Enthusiast

Registered: 01/06/06
Posts: 1371
Loc: IL
Originally Posted By: JR3
Bill,

No permanent marks. The blade is carbon as I do not like stainless knives. Yes, I was able to get a fire. I wish I had a picture just a few seconds later. Mrs. JR3 took that one.


I used to be in the same boat. I recently bought a Randall #16 SF (stainless only) and took it into the woods the other day. I must say it worked great I chopped down two good sized trees (5-6 inches across) and made some feather sticks for a fire. After, I then did some carving. After all this I get back to the house and do a paper test and it still cut through the paper almost like it did before I went out!

My model 14 wont be able to cut paper after less work! I touched up the 16 SF's edge on my leather strop (with green compound on it) and it was hair poping sharp again!

After my experience with the 16 SF now I feel the need for a stainless 14! The 16 SF is a great bush knife but its a little lighter than the 14 making it a great carry companion but not as good for chopping down a tree.


Edited by Leatherman (01/04/11 09:08 PM)
_________________________
Ben

Top
#84558 - 01/05/11 09:45 AM Re: Knife of the Week Model 18 [Re: Leatherman]
TAH Offline
Knife Enthusiast

Registered: 10/26/05
Posts: 2382
Loc: USA
Originally Posted By: Leatherman
This guy is striking with a 154CM steel blade and a laminated VG10 core blade with 420 J2 side steel (the 420 is on the spine) he's getting some good sparks!


Yep, he's using a Fällkniven knife. The sharp spine edges on their laminated stainless blades were designed to work well with a Swedish FireSteel. Also, FireSteels come with a stainless striker.

_________________________
Tom
RKS #4233

Top
#84572 - 01/05/11 05:19 PM Re: Knife of the Week Model 18 [Re: TAH]
WildBill Offline
Knife Enthusiast

Registered: 12/12/10
Posts: 51
That is the same firesteel I used in my test above. Works well.
_________________________
Bill
RKS#5892

Top
#84597 - 01/05/11 11:19 PM Re: Knife of the Week Model 18 [Re: WildBill]
Rob_Schoening Offline
Knife Enthusiast

Registered: 09/27/05
Posts: 480
Loc: Iowa.
Leatherman -
Details on your leather strop please.
- Rob
_________________________
Rob Schoening
www.lhgk.us

Top
#84598 - 01/05/11 11:28 PM Re: Knife of the Week Model 18 [Re: Rob_Schoening]
Leatherman Offline
Knife Enthusiast

Registered: 01/06/06
Posts: 1371
Loc: IL
This is my exact strop, purchased from KSF. I first bought it for my Bark River brand knives because they are convex but used it on my other knives too and it works wonders. I always finish off with the strop after I touch my knives to my Arkansas hones or after a days worth of work in the woods. The best part is it dose not wear your knives down like a stone would.

Also your edge will last longer if you use a strop, a fine edge lasts longer than a coarse edge!

http://www.knivesshipfree.com/product_info.php?cPath=637_638&products_id=6348
_________________________
Ben

Top
Page 11 of 51 < 1 2 ... 9 10 11 12 13 ... 50 51 >


Moderator:  Mr_Mod