Clinton Knives Nifeboy.com
The RANDALL KNIFE FORUMS

A place where EVERYBODY is welcome to join in on the discussion of Randall Made knives


Page 1 of 2 1 2 >
Topic Options
Rate This Topic
#166517 - 11/21/17 06:09 PM Sharpening Stone Help Please..............
byf41 Offline
Knife Enthusiast

Registered: 06/26/16
Posts: 18
I was hoping to get some help on these 2 stones I am wondering about . The 2 In question are the ones on top In all 4 pictures . I only show the lower stones for comparison . Both of the stones In question are very slightly longer than the ones shown for comparison by maybe .030-.040" . I know Randall used unmarked stones for awhile and was thinking the white one Is probably OK . Appreciate youre help guys .


Attachments
------IMG_1532.JPG

------IMG_1534.JPG

------IMG_1536.JPG

------IMG_1538.JPG



Top
#166559 - 11/22/17 05:46 PM Re: Sharpening Stone Help Please.............. [Re: byf41]
byf41 Offline
Knife Enthusiast

Registered: 06/26/16
Posts: 18
I guess I should have said would these 2 stones be correct for Randall knives ? The white one came with a 1970's #1 and the JP13 came with a 1960's #14 .

Top
#166562 - 11/22/17 06:38 PM Re: Sharpening Stone Help Please.............. [Re: byf41]
Tattoo Bill Offline
Knife Enthusiast

Registered: 07/14/15
Posts: 1907
Loc: Spring Hill, Florida
Originally Posted By: byf41
I guess I should have said would these 2 stones be correct for Randall knives ? The white one came with a 1970's #1 and the JP13 came with a 1960's #14 .


Yes they would.
_________________________
Tattoo Bill
Spring Hill, FL.
Livin On The Edge!
ta2bill@yahoo.com


Top
#168057 - 01/24/18 07:59 PM Re: Sharpening Stone Help Please.............. [Re: Tattoo Bill]
Sharpi Offline
Knife Enthusiast

Registered: 12/01/15
Posts: 645
So I picked this old Norton up at the flea $30
and the stones all have a small corner missing somewhere
and missing some screws no cover well looks good
The stones look good no bellies
best way to clean?
and do I need to fill it with oil or just apply as needed?
This one looks as old as Dirty Waters I think is Bo's old one
Thanks
Sharpi



Attachments
------Norton1.jpg

------Norton4.JPG

------Norton3.JPG

------Norton2.JPG




Edited by Sharpi (01/24/18 08:01 PM)
Edit Reason: punctuation

Top
#168059 - 01/24/18 08:19 PM Re: Sharpening Stone Help Please.............. [Re: Sharpi]
W Polidori Offline
Knife Enthusiast

Registered: 02/09/16
Posts: 5791
Loc: Central New York
Kerosene would be good to clean and to hone.
Stones have 2 sides, what's on the other side?
Light honing oil is probably the best choice. Need to soak the stones.


Edited by W Polidori (01/24/18 08:45 PM)
_________________________
Warren

Top
#168061 - 01/24/18 09:04 PM Re: Sharpening Stone Help Please.............. [Re: W Polidori]
Sharpi Offline
Knife Enthusiast

Registered: 12/01/15
Posts: 645
Warren
Thanks
Should I fill the reservoir with kerosene to soak
Sharpi

Top
#168070 - 01/24/18 10:33 PM Re: Sharpening Stone Help Please.............. [Re: Sharpi]
W Polidori Offline
Knife Enthusiast

Registered: 02/09/16
Posts: 5791
Loc: Central New York
First, consider the condition of the stones. Only you know the answer. Sticky, loaded, etc, just replace them IMO. The opposite side might just be fine. Report back.....
You can get replacement stones on ebay if you run into issues.


Edited by W Polidori (01/24/18 10:46 PM)
_________________________
Warren

Top
#168072 - 01/24/18 11:03 PM Re: Sharpening Stone Help Please.............. [Re: W Polidori]
Sharpi Offline
Knife Enthusiast

Registered: 12/01/15
Posts: 645
Warren
Not to sticky
Can I clean them with brake cleaner
Then honing oil
Thanks
Sharpi

Top
#168077 - 01/25/18 07:09 AM Re: Sharpening Stone Help Please.............. [Re: Sharpi]
GCTom41 Offline
Knife Enthusiast

Registered: 01/25/10
Posts: 2366
Loc: NY
You can soak the stones for a week or so in Mineral Oil.

Cleaning happens as you sharpen. What is in the pores will not release if it has been that way for a number of years.

Tom Flynn
_________________________
Tom Flynn
NRA Endowment
RKS#5918
RKCC-CM-178
SCI Life Member
DSC Life Member

Top
#168081 - 01/25/18 07:18 AM Re: Sharpening Stone Help Please.............. [Re: Sharpi]
desert.snake Offline
Knife Enthusiast

Registered: 09/25/13
Posts: 1111
Loc: the other side of the earth
Great exemplar!

Option A:
You can remove the stones from the mount,
put in a saucepan with soapy water and detergent
(powder to water ratio = 1 to 1)
and boil for 2-3 hours, at a temperature
of about 90-95 degrees Celsius, so that there
is no active boiling.

Option B:
Take the oven, heat up to 90-95 degrees Celsius,
take a baking tray and pour sand onto it,
put the stones on the sand and sprinkle around,
how to create a mound.
This is necessary for uniform warm-up. Warm 2-3 hours.

You can repeat several times to clear the stones better,
you can use both methods alternately.

Then the surface can be cleaned with kerosene.
_________________________
Si vis pacem, para bellum

Top
Page 1 of 2 1 2 >


Moderator:  Mr_Mod